document number: 37004 revision 05-dec-00 www.vishay.com 2 APD-016M040 vishay dale plasma panel display modules 16 character display with drive electronics and controller features ? 16 (1 x 16) alphanumeric characters (5 x 7 dot matrix). ? bezel and filter included. ? parallel and serial interfaces. ? high brightness. ? wide viewing angle (150 ). ? low input voltage. ? compact size. ? enhanced replacement for burroughs ssd1000-0061 (optionally-0041). optical specifications viewing area: 0.40" [10.2mm] w x 6.69" [169.9mm] l. number of characters: 16. character size: 0.28" [7.1mm] w x 0.40" [10.2mm] h. pixel size: 0.036" [0.914mm] diameter. pixel pitch: 0.061" [1.55mm]. character spacing: 2 blank columns between successive characters - 0.147" [3.73mm]. luminance: 80 foot lamberts. the APD-016M040 has two modes of operation, parallel or serial input. the parallel interface consists of a 6 bit data bus plus 3 hand-shaking and 3 control lines. new charac- ters are entered from right to left by presenting the appropri- ate 6 bit code to the data bus and latching it into memory with a data present pulse. a write cycle output signal is provided during the time in which data can be written to the display, and a data taken pulse occurs after data has been accepted, or when back space occurs. back space allows the displayed message to be shifted to the right, recalling the last character shifted off the left end of the display. up to 16 characters may be recalled, after which blanks are entered in the left position of the display. the display may be cleared at any time by bringing the clear line low. a blank disable line is provided to blank the display without altering the refresh memory contents. the serial interface is rs-232-c compatible and has 3 selectable baud rates (300, 1200, 9600). this mode assumes 1 start bit, 8 data bits, 1 stop bit, no parity and half duplex. no handshaking is provided. mode settings and baud rates are selected as follows. (both lines are internally pulled to vcc with 6.8 kilohm pull-up resistors.) ss0 ss1 baud rate 0 0 300 0 1 1200 1 0 9600 1 1 parallel pin description pin description 1 data bit 5 a data bit 4 2 data bit 3 b data bit 2 3 data bit 1 c data bit 0 4 n/c d data present 5 clear e back space 6 speed select 1 f data taken 7 write cycle h received data 8 blank disable j + 5 v 9 speed select 0 k n/c 10 n/c l gnd pin description keyway between pins 4 (d) and 5 (e). *vcc is the input to a dc-dc converter. there may be peak in rush currents higher than shown. standard electrical specifications symbol min. typ. max. units supply voltage vcc 4.75 5 5.25 v supply current (1) icc 1.25 1.75 a logic one voltage vih 2 v logic ? voltage vil 0.8 v
www.vishay.com 3 APD-016M040 vishay dale document number: 37004 revision 05-dec-00 dimensions in inches [millimeters] 2.40 [61.0] ref. c of pad #1 l 7.15 [181.6] 0.156 [3.96] c - c ll 1.70 [43.2] 2.25 [57.2] 0.680 [17.27] 0.820 [20.8] 0.720 [18.3] mates with dale eb81-a10gx-d or equivalent 1.96 [49.8] max 1.81 [46.0] max. 0.185 [4.70] 8.50 [215.9] display area description part no. display and electronics (includes bezel) (equivalent to burroughs ssd1000-0061) ............................................... ............. APD-016M040 display and electronics (includes bezel) data entry is left to right (equivalent to burroughs ssd1000-0041) .............. apd- 016m040-1 mating connector ............................................................................................................... ........................................................... 280498-01 ordering information
|
